Build your own photographic developing trays
Trays are the quiet workhorses of a darkroom. The moulded plastic ones sold in every camera shop come in a handful of sizes, none quite match the paper you print, and all of them have been shipped halfway around the world before they reach your bench. Building your own developing trays solves the sizing problem, gives you a floor that drains in one direction, and often costs less than the trays it replaces.
This guide covers planning, cutting, joining and sealing, in millimetres and litres, for anyone printing from negatives or wet plates in Australia — in a share house bathroom, a suburban garage or a community printshop. If you work with wet collodion, there are notes on chemistry compatibility below.
Why build trays yourself
Standard trays are designed for a generic 8x10 inch sheet and a shallow bath. That works right up until you print A3 or A2, or your developer needs enough depth to keep a print submerged and flat instead of curling at the corners. A tray built to measure solves both, and you can lay the floor with a slight fall toward one corner so spent chemistry pours off in a single tilt rather than sloshing over the edge.
Freight is the other argument. A stack of imported trays has paid for shipping before you unpack it, while a sheet of 304 stainless or a few perspex offcuts often costs less than two factory trays and lasts decades. It is the sort of gear plenty of people in the trade are keen to make rather than keep ordering.
The same standard applies in a working darkroom, not just a hobby one. As Meg Turner's biography explains, her practice moves between wet collodion, film, darkroom printing and installation work, and her trays have to take silver nitrate, collodion solvent and paper developer without warping or holding residue.
Choosing materials that survive the chemistry
Developing trays live in a hostile environment: caustic developer, alkaline stop bath, ammonium thiosulphate fixer and the occasional splash of silver nitrate. The surface must be non-porous, chemically inert and easy to wipe down. 304 stainless is the safest all-rounder; 316 is worth the extra few dollars if you print in coastal humidity — Darwin, Cairns, Townsville — where mild steel starts weeping rust.
Perspex and acrylic work beautifully for paper trays: light, cheap and easy to cut, though they scratch and can craze if acetone or thinner lands on them. Food-grade HDPE gives you a flexible option, and an old glass storage box can be converted. For wet plate collodion, test a drop of your solvent on an offcut first and choose stainless or glass if it dulls the surface.
Leave galvanised steel, bare aluminium, brass and copper alone. Untreated ply and MDF are out too — they swell, they smell, and the formaldehyde from MDF is not something you want in a small room with the door shut.
Sizing trays for the paper you print
Paper here comes in imperial and A sizes, so work in millimetres: 8x10 inch is 203 by 254, A3 is 297 by 420, A2 is 420 by 594. Allow about ten millimetres of clearance around each edge so a print slides in without catching, and round the internal corners so a sharp angle cannot crease a sheet.
Depth is the next call. A 30 to 40 millimetre wall gives a tray light enough to agitate by tilting and deep enough to keep a print covered by ten millimetres or so of developer. Twenty millimetres is plenty for stop bath or a wetting tray. Keep separate trays for developer, stop and fix, because cross contamination flattens highlights and shortens paper life.
For prints at 40 by 50 centimetres or larger, skip trays entirely and build a print washer, or wash directly in the sink with a plastic squeegee pulling water across the sheet. A tray you have to dunk and lift is a slow way to work.
Cutting, folding and joining
Mark the sheet with a steel rule and a fine marker, then cut acrylic with a jigsaw and a fine-tooth blade at low speed, or score and snap for straight runs. Stainless wants tin snips or a jigsaw. File the edges and sand the floor: a burr will tear a print, and a scratch in the floor prints as a white line.
Join perspex with acrylic solvent cement, clamp it and leave it overnight; the cement welds the plastic and the joint ends up stronger than the sheet. Stainless usually gets a folded flange, three millimetre holes, countersunk pop rivets. If you prefer timber, build a carcass in six millimetre ply and line it with sheet plastic, sealing every seam.
Give the floor a three to five millimetre fall toward one corner, or drill a six millimetre drain hole at the low point and file it round. A hole is easier to scrub than a seam and stops chemistry pooling in the corner where it dries into a crust. Add rubber feet so the tray does not skate across a wet bench.
Draining, rinsing and disposing of chemistry
Work out where the water goes before you build. A plumbed sink takes rinse water straight after use, and a bucket with a standpipe works in a shared room where you cannot leave a tap running. Rinse trays at the end of the session, while you are still in the mood to do it properly.
Never tip developer or fixer down a stormwater drain. In Australia that water runs to local creeks and estuaries, from Sydney Harbour to the Yarra and the Swan, and spent fixer carries silver worth recovering. Councils run household hazardous waste drop-off days for the small volume a darkroom makes, and some fixers collect your spent solution if you keep it in labelled containers.
Ventilation matters more than people expect. Fixer smells like a burst bulb, and a share house bathroom at the end of a long arvo is the worst place to find that out. A window that opens, a fan that actually moves air, and a habit of rinsing under running water will keep the room bearable.
Tools and materials worth buying locally
Most of this comes from a hardware trade counter, a plastics supplier or a second-hand shop, and there is no need to drive around all afternoon: chains like Bunnings and Mitre 10 do click and collect from the trade desk, and Australian prices include 10 per cent GST.
- A jigsaw with a fine-tooth blade, a steel rule, square and fine marker
- Tin snips plus a 3 mm drill, countersink and pop rivets for stainless
- Acrylic solvent cement and clamps for welding perspex joints
- 320 grit wet-and-dry paper, a soft brush and rubber feet
- 1.2 mm 304 stainless sheet from a trade counter, or 316 from a stainless specialist
- 3 to 4 mm perspex offcuts salvaged from old display cabinets
- Food-grade 6 mm HDPE sheeting for a flexible liner
- Epoxy or solvent cement and a non-slip mat to keep the tray steady
The Salvo and local op shops are worth a poke for acrylic: newsagents and record shops chucks out perspex display cabinets, and one cabinet front can yield sheet for a couple of trays. Plastics suppliers cut perspex to your measurements for a few dollars, and a laser cutting bureau can cut a full set in an afternoon.
Get started with your first tray
Decide whether the tray is a tool or part of your own practice. A wet collodion tray has to be boringly reliable; a gallery tray can carry a painted panel or your studio mark on the outside, keeping the inside plain so nothing contaminates the bath. Hand-painted surfaces have a long history in workshops and darkrooms, and the story of hand-painted movie poster craft shows what a blank sheet of metal or acrylic becomes when somebody takes their time with it.
Label the outside with masking tape and a marker, or a laminated sticker, so the developer, stop and fix trays never get swapped. Paint the outside only, with a water-based enamel, and let it cure fully before the tray sees any chemistry. Clean perspex with a soft brush and lukewarm water, never steel wool, and store trays upright rather than nested so one does not scratch the next.
Start with one tray in the size you print most, test it with a test strip, then build the rest. For larger runs, contract printing is Meg's other hat: she prints for other artists and has worked with community printshops, so send a note with your paper sizes, chemistry and volume and you will get back a plan, a price and a timeline. The same route works for a hands-on workshop on making and using trays — a session with real chemistry beats another video.